Pools & Water Features

How to Install an Electrical Outlet for a Wall Fountain

by Furnishly | Oct 24, 2022 | DIY, Home Improvement

A wall fountain gives you the relaxing feeling of sitting next to a babbling brook right outside your home.

By installing a ready-made one like this one, you don’t have to rework any plumbing in your home. All you need to do is decide on the location, drive in a mounting screw, and hang the fountain.

However, if you don’t have an electrical outlet nearby, you’ll need to have one installed for your wall fountain to work.

Electrical work is best done by professionals. Here’s what they’ll do to set up an exterior outlet.

Installing an Exterior Electrical Outlet

Electrician uses tape measure to find distance from outlet to door — The fountain will be hung on the other side of this wall, so we can use the wires from this outlet to power an exterior outlet. (3 Echoes Content Studio)

The electrician will find an interior outlet near where you want the exterior outlet to be. He’ll use the wires from this outlet to power the exterior outlet.

Hole in wall with electrical wires coming out — To access the wires, the electrician must first remove the electrical box. (3 Echoes Content Studio)

With the power turned off, he’ll disconnect the outlet and remove the box.

Hand using pencil to mark around an electrical box — To mark the location for the new exterior outlet, the electrician uses a pencil and the electrical box. (3 Echoes Content Studio)

Next, the electrician will mark the location of the new box with a pencil. Make sure the electrician centers the box under the wall fountain.

The electrician runs the wire through the electrical box to connect it to the wall. (3 Echoes Content Studio)

After cutting a hole for the exterior electrical box, he’ll fish a new wire through that hole over to the inside box location.

Using a screwdriver to secure a GFCI outlet to a home's exterior — A ground fault circuit interrupter outlet like this one constantly track electrical current flow; if they detect a change, they immediately cut power to the outlet. (3 Echoes Content Studio)

Finally, the electrician will secure and wire the new box with a ground fault circuit interrupter outlet, which the local building code requires for outside locations.

Hands plugging in a pump to a wall fountain — The pump in the wall fountain recirculates the water. (3 Echoes Content Studio)

Once the electrical work is complete, all that’s left to do is connect the wall fountain’s pump and fill it with water before plugging it into the new outlet.

Now, we can begin enjoying the relaxing sound of water falling gently.

3 Ways to Clean Pool Coping | Ep. 175

by Furnishly | Jun 17, 2022 | DIY, Home Improvement

Stone paver pool coping next to stone tile — Pool coping keeps water from damaging a pool’s outer shell. (TerryJ, Getty Images Signature)

Pool coping creates a barrier around a pool’s edge to protect it from the surrounding surface and keep water from damaging the outer shell.

While the coping prevents water damage, the pool water can sometimes leave calcium deposits behind.

This is the problem for Craig Jackson in Novato, Calif. He asks, “What’s the best way to clean off these hardened deposits?”

Calcium deposits can build up on pool coping like on a glass shower door. This happens when the pH levels in the pool water are off.

Here are three options for cleaning it:

TSP: When diluted in water, trisodium phosphate is a mild-all around cleaner that removes calcium buildup and oily residue.
Calcium and lime remover: Use a commercial-grade calcium, lime and rust remover, like ZEP Calcium, Lime and Rust Remover.
Pumice stone: To clean the buildup without using chemicals, use a pumice stone to scrub the calcium deposits away. It won’t harm pool water and its soft stone surface won’t scratch the pool coping.

Once the calcium build-up is gone, use a clear sealer to prevent it from coming back.

Cantilevered concrete pool coping — Concrete is the most cost-friendly material for pool coping. (edenexposed, Getty Images Signature)

FAQ About Pool Coping

What is the best coping to put around a pool?

Tile, brick, stone, concrete, composite, or even wood are used for pool coping. The most commonly used material is sandstone because of its non-slip properties.

Is pool coping expensive?

Pricing depends on the material used. Sandstone, the most common pool coping material, costs $40–$55 per linear foot. Conversely, cantilevered concrete coping typically costs $6–$10 per linear foot.

What goes between pool coping and concrete/pavers?

Whatever material you choose for your pool coping, the installation is basically the same. The coping is caulked or filled with elastomeric sealant onto the concrete surrounding the pool. An elastomeric sealant allows for some expansion and contraction, so the pool coping won’t crack during temperature shifts.

Skip to [25:05] for the full segment on the Today’s Homeowner Podcast.

Also on this episode:

Best New Product

Simple Solutions

Metal colander converted into a hanging planter — Give an old metal colander a new purpose by turning it into a hanging planter.

Hanging Colander Planter — Make a unique hanging planter out of a metal colander!

Start by drilling three holes evenly spaced around the rim of the colander.
Next, spray paint the colander to match the house trim.
Then, hang it with three 16-inch chains and S-hooks.
Line the colander with landscaping fabric or coffee filters before adding soil and plants.

Watch: How to Upcycle a Colander Into a Hanging Planter

Tub drain with hard water stain — Remove hard water stains with household items you have on hand. (skhoward, Getty Images Signature)

Tub-Stain Remover — This recipe is great for removing stains from tubs, sinks and toilets.

Mix equal amounts of cream of tartar and baking soda with enough lemon juice to make a paste.
Rub the mixture into the stain with your fingers or a soft cloth.
Let sit for a half-hour, then rinse with water.